View DL126TRD_705096.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

DL126TRS/D Tape & Reel and Packaging Specifications for Small-Signal Transistors, FETs and Diodes
Excerpted from the ON Semiconductor Small-Signal Transistors, FETs and Diodes Device Data Book, DL126/D. http://onsemi.com
Embossed Tape and Reel is used to facilitate automatic pick and place equipment feed requirements. The tape is used as the shipping container for various products and requires a minimum of handling. The antistatic/conductive tape provides a secure cavity for the product when sealed with the "peel-back" cover tape.
* * * * *
Two Reel Sizes Available (7 and 13) Used for Automatic Pick and Place Feed Systems Minimizes Product Handling EIA 481, -1, -2 SOT-23, SC-59, SC-70/SOT-323, SC-75/SOT-416/SC-90, SC-88/SOT-363,
* *
SC-88A/SOT-353, SC-74/TSOP-6, SOD-123, SOD-323 in 8 mm Tape SOT-89, SOT-223 in 12 mm Tape SO-16 in 16 mm Tape
Use the standard device title and add the required suffix as listed in the option table below (Table 1). Note that the individual reels have a finite number of devices depending on the type of product contained in the tape. Also note the minimum lot size is one full reel for each line item, and orders are required to be in increments of the single reel quantity.
Table 1. EMBOSSED TAPE AND REEL ORDERING INFORMATION
Package Tape Width (mm) 8 8 8 8 8 8 8 8 8 8 8 8 12 12 12 16 16 Pitch mm (inch) 4 4 4 4 4 4 4 4 4 8 8 8 Reel Size mm (inch) 178 330 178 178 330 178 178 178 178 178 330 178 178 178 330 178 330 (7) (13) (7) (7) (13) (7) (7) (7) (7) (7) (13) (7) (7) (7) (13) (7) (13) Devices Per Reel and Minimum Order Quantity 3,000 10,000 3,000 3,000 10,000 3,000 3,000 3,000 3,000 3,000 10,000 3,000 1,000 1,000 4,000 500 2,500 Device Suffix T1 T3 T1 T1 T3 T1 T1 T1 T1 T1 T3 T1 T1 T1 T3 R1 R2
SOT-23 SC-59 SC-70, SOT-323 SC-75, SOT-416, SC-90 SC-88, SOT-363 SC-88A, SOT-353 SC-74, TSOP-6 SOD-123 SOD-323 SOT-89 SOT-223 SO-16
(c) Semiconductor Components Industries, LLC, 2001
1
November, 2001 - Rev.2
Publication Order Number: DL126TRS/D
DL126TRS/D
EMBOSSED TAPE AND REEL DATA FOR DISCRETES
T Max Outside Dimension Measured at Edge
1.5 mm Min (.06) A 20.2 mm Min (.795)
13.0 mm 0.5 mm (.512 .002) 50 mm Min (1.969)
Full Radius
G
Inside Dimension Measured Near Hub
Size 8 mm 12 mm 16 mm 24 mm
A Max 330 mm (12.992) 330 mm (12.992) 360 mm (14.173) 360 mm (14.173)
G 8.4 mm + 1.5 mm, -0.0 (.33 + .059, -0.00) 12.4 mm + 2.0 mm, -0.0 (.49 + .079, -0.00) 16.4 mm + 2.0 mm, -0.0 (.646 + .078, -0.00) 24.4 mm + 2.0 mm, -0.0 (.961 + .070, -0.00)
T Max 14.4 mm (.56) 18.4 mm (.72) 22.4 mm (.882) 30.4 mm (1.197)
Figure 1. Reel Dimensions
Metric Dimensions Govern -- English are in parentheses for reference only
SOD-323, SOD-123
8 mm
SC-59, SC-70, SC-75, SOT-23
8 mm
SC-88, SOT-363 T1 Orientation
8 mm
SC-88A, SOT-353 T1 Orientation
8 mm
TSOP-6, SC-74 T1 Orientation
8 mm
SOT-89 R1 Orientation
12 mm
SOT-223
12 mm
SO-16
16 mm
Direction of Feed
Figure 2. Typical Reel Orientations
http://onsemi.com
2
DL126TRS/D
Figure 3. CARRIER TAPE SPECIFICATIONS
10 Pitches Cumulative Tolerance on Tape 0.2 mm ( 0.008) E Top Cover Tape A0 B0 P Embossment Center Lines of Cavity D1 For Components 2.0 mm x 1.2 mm and Larger
K t D
P0 P2
F
W
B1
K0 See Note 1
For Machine Reference Only Including Draft and RADII Concentric Around B0
User Direction of Feed * Top Cover Tape Thickness (t1) 0.10 mm (.004) Max.
Bar Code Label R Min Tape and Components Shall Pass Around Radius "R" Without Damage Bending Radius 10 Maximum Component Rotation Typical Component Cavity Center Line Embossed 100 mm Carrier (3.937) 1 mm Max
Embossment
Tape 1 mm (.039) Max 250 mm (9.843) Camber (Top View) Allowable Camber To Be 1 mm/100 mm Nonaccumulative Over 250 mm
Typical Component Center Line
Table 2. DIMENSIONS
Tape Size 8 mm 12 mm 16 mm 24 mm B1 Max 4.55 mm (.179) 8.2 mm (.323) 12.1 mm (.476) 20.1 mm (.791) D 1.5+0.1 mm -0.0 0.0 (.059+.004 -0.0) D1 1.0 Min (.039) 1.5 mm Min (.060) (.060 ) E 1.750.1 mm (.069.004) (.069.004 ) F 3.50.05 mm (.138.002) 5.50.05 mm (.217.002) 7.50.10 mm (.295.004) 11.50.1 mm (.453.004) K 2.4 mm Max (.094) 6.4 mm Max (.252) 7.9 mm Max (.311) 11.9 mm Max (.468) P0 4.00.1 mm (.157.004) (.157.004 ) P2 2.00.1 mm (.079.002) (.079.002 ) R Min 25 mm (.98) 30 mm (1.18) (1.18 ) T Max 0.6 mm (.024) (.024 ) W Max 8.3 mm (.327) 12.30 mm (.470.012) 16.3 mm (.642) 24.3 mm (.957)
Metric dimensions govern -- English are in parentheses for reference only. 1. A0, B0, and K0 are determined by component size. The clearance between the components and the cavity must be within 0.05 mm min. to 0.50 mm max., the component cannot rotate more than 10 within the determined cavity. 2. If B1 exceeds 4.2 mm (0.165) for 8 mm embossed tape, the tape may not feed through all tape feeders. 3. Pitch information is contained in Table 1. Embossed Tape and Reel Ordering Information on pg. 1.
http://onsemi.com
3
DL126TRS/D
TO-92 EIA, IEC, EIAJ Radial Tape in Fan Fold Box or On Reel
Radial tape in fan fold box or on reel of the reliable TO-92 package are the best methods of capturing devices for automatic insertion in printed circuit boards. These methods of taping are compatible with various equipment for active and passive component insertion.
US/European Suffix Conversions
US RLRA RLRE RLRM EUROPE RL RL1 ZL1
* * * * * *
Available in Fan Fold Box Available on 365 mm Reels Accommodates All Standard Inserters Allows Flexible Circuit Board Layout 2.5 mm Pin Spacing for Soldering EIA-468, IEC 286-2, EIAJ RC1008B
Package Suffixes
Device Suffix (None) RLRA Leadform Type Straight Leadformed Leadformed Leadformed Leadformed Shipping 5000/Bag 2000/Tape & Reel 2000/Tape & Reel 2000/Fan Fold Box 2000/Fan Fold Box
Ordering Notes:
When ordering radial tape in fan fold box or on reel, specify the style per Figures 4 through 7. Add the suffix "RLR" and "Style" to the device title, i.e. MPS3904RLRA. This will be a standard MPS3904 leadformed, radial taped and supplied on a reel per Figure 4. Fan Fold Box Information -- Order in increments of 2000. Reel Information -- Order in increments of 2000.
RLRE RLRM RLRP
CARRIER STRIP ADHESIVE TAPE
ROUNDED SIDE
CARRIER STRIP ADHESIVE TAPE FLAT SIDE
FEED
FEED
Rounded side of transistor and adhesive tape visible.
Flat side of transistor and adhesive tape visible.
Figure 4. Style A
Figure 5. Style E
http://onsemi.com
4
DL126TRS/D
FLAT SIDE
Style M fan fold box is equivalent to styles E and F of reel pack dependent on feed orientation from box.
Dimensions for Device Positioning on Tape for Fan Fold Box
Specification Inches Symbol
D D2 F1, F2 H H1 H2A H2B H4 H5 L L1 P P1 P2 T
Tape Feedhole Diameter Component Lead Thickness Dimension Component Lead Pitch Bottom of Component to Seating Plane Feedhole Location Deflection Left or Right Deflection Front or Rear Feedhole to Bottom of Component Feedhole to Seating Plane Defective Unit Clipped Dimension Lead Wire Enclosure Feedhole Pitch Feedhole Center to Center Lead First Lead Spacing Dimension Adhesive Tape Thickness
CCCCCCC CCCCCCC CCCCCCC CCCCCCC
Figure 6. Style M
H2A H H4 H5 P2 P1
ADHESIVE TAPE ON TOP SIDE
ADHESIVE TAPE ON TOP SIDE ROUNDED SIDE CARRIER STRIP
CARRIER STRIP
FLAT SIDE OF TRANSISTOR AND ADHESIVE TAPE VISIBLE.
ROUNDED SIDE OF TRANSISTOR AND ADHESIVE TAPE VISIBLE. Style P fan fold box is equivalent to styles A and B of reel pack dependent on feed orientation from box.
Figure 7. Style P
H2A
H2B
H2B
W2 T1 L1 L F1 H1 W1 W T T2 P2 P D
F2
Figure 8. Device Positioning on Tape
Millimeter Max Min
3.8 0.38 2.4 1.5 8.5 0 0 18 15.5 8.5 2.5 12.5 5.95 3.55 0.15
Item
Min
0.1496 0.015 0.0945 .059 0.3346 0 0 0.7086 0.610 0.3346 0.09842 0.4921 0.2342 0.1397 0.06
Max
4.2 0.51 2.8 4.0 9.5 1.0 1.0 19.5 16.5 11 -- 12.9 6.75 3.95 0.20
0.1653 0.020 0.110 .156 0.3741 0.039 0.051 0.768 0.649 0.433 -- 0.5079 0.2658 0.1556 0.08
http://onsemi.com
5
DL126TRS/D
Dimensions for Device Positioning on Tape for Fan Fold Box
Specification Inches Symbol
T1 T2 W W1 W2
Millimeter Min
-- 0.35 17.5 5.5 .15
Item Overall Taped Package Thickness Carrier Strip Thickness Carrier Strip Width Adhesive Tape Width Adhesive Tape Position
Min
-- 0.014 0.6889 0.2165 .0059
Max
0.0567 0.027 0.7481 0.2841 0.01968
Max
1.44 0.65 19 6.3 0.5
NOTES:
1. Maximum alignment deviation between leads not to be greater than 0.2 mm. 2. Defective components shall be clipped from the carrier tape such that the remaining protrusion (L) does not exceed a maximum of 11 mm. 3. Component lead to tape adhesion must meet the pull test requirements established in Figures 5, 6 and 7. 4. Maximum non-cumulative variation between tape feed holes shall not exceed 1 mm in 20 pitches. 5. Holddown tape not to extend beyond the edge(s) of carrier tape and there shall be no exposure of adhesive. 6. No more than 1 consecutive missing component is permitted. 7. A tape trailer and leader, having at least three feed holes is required before the first and after the last component. 8. Splices will not interfere with the sprocket feed holes. CORE DIA. 82mm 1mm
ARBOR HOLE DIA. 30.5mm 0.25mm 330 mm 13" MAX 252 mm MAX 9.92" MARKING NOTE
HUB RECESS 76.2mm 1mm RECESS DEPTH 9.5mm MIN 365mm + 3, - 0mm 38.1mm 1mm 48 mm MAX
58 mm 2.28" MAX
Figure 9. Fan Fold Box Dimensions
Material used must not cause deterioration of components or degrade lead solderability
Figure 10. Reel Dimensions
ADHESION PULL TESTS
500 GRAM PULL FORCE 100 GRAM PULL FORCE
16 mm
70 GRAM PULL FORCE
16 mm
HOLDING FIXTURE
HOLDING FIXTURE
HOLDING FIXTURE There shall be no deviation in the leads and no component leads shall be pulled free of the tape with a 500 gram load applied to the component body for 3 1 second.
The component shall not pull free with a 300 gram load applied to the leads for 3 1 second.
The component shall not pull free with a 70 gram load applied to the leads for 3 1 second.
Figure 11. Test #1
Figure 12. Test #2
Figure 13. Test #3
http://onsemi.com
6
DL126TRS/D
Notes
http://onsemi.com
7
DL126TRS/D
Thermal Clad is a trademark of the Bergquist Company.
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-0031 Phone: 81-3-5740-2700 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative.
http://onsemi.com
8
DL126TRS/D

▲Up To Search▲

Price & Availability of DL126TRD

	To Download DL126TRD Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .